BPATCH

Section: User Commands (1)
Index Return to Main Contents
 

NAME

bpatch - binary patch and dump file utility  

SYNOPSIS

bpatch [ -b blksize ] [ -d ] [ -D pagecnt ] [ -e ] [ -p ] [ -r reclen ] [ -s ] [ -x ] file...  

DESCRIPTION

Bpatch allows the viewing and/or modification of files, independent of file type (text, executable, data file, and so forth). Bpatch allows the data to either be examined at the terminal, dumped to a print device or file, or edited in the general manner of vi(1). The data in the file is dumped or displayed in pages of 256 bytes.  

Options

-b blksize
The -b option specifies the blocksize of the data file. This is used primarily with tapes, and is allowed only with one of the dump (-d or -D) options. When this option is specified, the file is opened in readonly mode.
-d
The -d option indicates that a dump (no terminal manipulation) is to be performed. The entire file will be dumped to standard output. No editing of the data is allowed and the file is opened in readonly mode.
-D pagecnt
The -D option is similar to the -d option, with the following exception: the pagecnt argument limits the dump to the specified number of pages.
-e
The -e option indicates that the file contains EBCDIC data and should be converted in the character portion of the dump.
-p
Used with one of the dump options, this option causes the program to pause between pages. The program will then wait for the user to press either the return key to continue, or the DEL (or rubout) key to stop the dump.
-r reclen
The -r option indicates the record length of the data within the dump. When specified, this option causes bpatch to place a colon (:) between the last byte of one record and the first byte of the next.
-s
This option turns on the byte swap option. It may be toggled dynamically during execution (see -x under Commands below).
-x
This option specifies the suppression of pages that contain only NUL characters. The result is that only the page header (name and page number) will appear for such a page. This option may only be used with one of the dump options.
 

Arguments

file
Any number of files may be specified.
 

Commands

All commands are valid only in the non-dump, interactive mode. Commands may be entered in either upper or lower case. Commands of the form '^x' indicate that the control character x is to be entered. All commands that request movement within a file or between files cannot be executed if any changes have been made. To proceed in this case, the user must either enter the w command, the u command, or the r command. Requesting a next or previous file when there is no such will cause the issuance of an error message. Note that certain commands allow/require either some text or numeric value. In those cases, the user should type in characters and end the string with either a <cr> or <DEL>.
?
Display the help screen. The help screen will remain until the user either redraws the screen (see ^r) or changes pages or files.
!
Execute the following command in the shell.
backslash
Display the previous page.
<cr>
Display the next page.
DEL
Quit the program if no changes have been made.
/
This command initiates an ASCII search. The text entered on the command line will be used as a search string, and the file will be searched starting with the current page. When the string is found, the page containing the string will be displayed. If the string is not found, an apapropriate message will be displayed.
^f
Open a named file whose name will be entered on the command line and followed either by <cr> or DEL.
^n
Open the next file and display the first page.
^p
Open the previous file and display the first page.
^q
Quit without writing current changes.
^r
Redraw the screen.
NNN
Entering a numeric value requests that the specified page be displayed.
-x
Toggle the command line option represented by x:
a
Toggle display to ascii (assume data is ascii).
e
Toggle display to dbcdic (assume data is ebcdic).
s
Toggle byte swap.
a
Edit the ASCII display. End edits by pressing the DEL key. All other characters will be treated as valid input. Cursor movement keys (arrows and home) allow movement within the edit window. Nonprinting characters are displayed as dot (.) in this window.
f
Display the first page in the current file.
g
Display the page containing the byte address typed in following the command.
h
Edit the HEXADECIMAL display. End edits by pressing DEL key. Cursor movement keys (arrows and home) allow movement within the edit window. Two keystrokes are required to modify a byte, and both must be valid hexadecimal values (0-9 and a-f). To cancel a change after typing one character, press DEL.
l
Display the last page in the current file.
q
Quit the file. A warning will be issued if any changes have been made but not written out.
r
Reread the current page.
u
Undo all changes to the current page.
w
Write out the current page.
 

SEE ALSO

od(1)

 

Index

NAME
SYNOPSIS
DESCRIPTION
Options
Arguments
Commands
SEE ALSO
This document was created by man2html, using the manual pages.
Time: 04:07:23 GMT, December 02, 2024